Description
IMPORTANT NOTES
1. UPDATE YOUR FIRMWARE: Please upgrade the firmware on your POD Go and POD Go Edit software from Line 6 to the latest before installing this patch. Even if your POD Go is up to date, the app needs to be updated as well. If you get an error importing a patch, the problem is most likely outdated firmware on your POD Go or POD Go Edit.
2. IR CAB INCLUDED: This download includes a premium IR cab from our ’63 B-MAN OXFORD IR pack. This IR is are essential to this patch, as they allow the stock Bassman amp model to take on the character of Brian’s vintage 1963 Fender Bassman amp.
Here is the specific IR included, and it’s location in our POD Go:
- WT B-MAN Oxford 121+SR25 (To purchase more IR packs, visit the the Worship Tutorials IR Cab page).
3. INCLUDED PATCHES: This download includes two patches:
- 63 Bassman WT SC. This is the main patch with the IR Cab voiced for single coils
- 63 Bassman WT HB. This is the main patch with the IR Cab voiced for humbuckers
- 63 Bassman FX 1. This patch includes additional effects blocks from our full Helix patch (see signal chain section below to know what is included)
- 63 Bassman FX 2. This patch includes more additional effects blocks from our full Helix patch (see signal chain section below to know what is included)
*We include the additional ‘FX’ patches so you can mix and match effects blocks to best suite your needs. These additional blocks include more drive, delay, reverb, and modulation options.
HOW TO IMPORT THIS PATCH AND IR
- Connect your POD Go to your computer using a USB Cable
- Download and instal the ‘POD Go Edit’ app from Line 6
- In the ‘POD Go Edit’ app, drag and drop the patch into a slot in the ‘PRESETS’ column
- To import an IR, switch to the ‘IMPULSES’ column (next to the PRESETS column), and drag & drop the IR into the appropriate slot (see note above).
- PLEASE NOTE: If you do not have the IR loaded into the ‘IMPULSES’ column, the patch will not sound correct, even if you have the IR block on – you must drag and drop the IR into the IMPULSES column.
SIGNAL FLOW AND EFFECTS
MAIN PATCHES
- Input
- Wah – Not set up
- Deluxe Comp – not mapped to a switch, always on
- Scream 808 – Tube Screamer Overdrive – mapped to foot switch A
- Volume (log curve) – mapped to EXP 2
- Amp – Tweed Blues Arts (gain mapped to foot Switch B – see notes below)
- Cab/IR – see above for IR info
- Cali Q Graphic – Always on EQ – Use this EQ to make tonal tweaks for your guitar/setup. These controls will affect your tone differently than the amp controls. See below for recommended settings.
- Digital Delay (legacy) – parameters mapped to foot switches A and C (see notes below)
- Dynamic Hall – parameters mapped to foot switch D (see notes below)
FX 1 PATCH:
- In
- Volume
- Wah (not set up)
- Amp (not set up)
- Cab (not set up)
- EQ (not set up)
- Heir Apparent
- Transistor Tape (1/4 delay)
- Transistor Tape – 1/8 note delay
- Dual Delay – 1/8 + 1/8d delay
- Out
FX2 PATCH:
- Input
- Volume
- Wah (not set up)
- Amp (not set up)
- Cab (not set up)
- EQ (not set up)
- Tremolo
- Plate Reverb
- Glitz Reverb
- Out
USAGE
This patch is meant to be used in either stompbox or snapshot mode. We recommend setting up your POD Go to use switches A, B, C, and D as stomps, and the left up/down switches to cycle through snapshots.
We have included additional ‘FX” patches so you can copy and paste the various effects blocks used in the full Helix version of this patch to suite your needs with the POD Go.
AMP GAIN – FOOT SWITCH B:
Foot switch B adjusts the Drive parameter on the amp block. This gives you a true amp overdrive tone without the use of dirt pedals. If the base patch is too dirty for your preference, adjust the ‘Min Drive’ and ‘Max Drive’ settings on this button to suite your needs. The ‘Min Drive’ settings is when the button is off, and the ‘Max Drive’ setting is when the button is on.
DELAY – FOOT SWITCHES A and C:
Foot switch C adjusts the following parameters in the Transistor Tape Delay block: Note Sync, Feedback, and Mix. In the ‘off (min)’ position, you get a subtle 1/4 note delay. In the ‘on (max)’ position, you get a bigger dotted 8th note delay. Footswitch A turns the delay on and off.
REVERB – FOOT SWITCH D:
Foot switch D adjusts the following parameters in the Glitz Reverb block: Decay and Mix. In the off/min position you get a subtle reverb, and in the on position you get a big ambient reverb.
SNAPSHOTS:
There are four snapshots included in this patch to get different sounds. They are:
- Snapshot 1: CLEAN. This is the base clean tone with delay.
- Snapshot 2: DRIVE. Light overdrive.
- Snapshot 3: P&W LEAD: Big drive with delay and lots of verb. This is a typical P&W style drive.
- Snapshot 4: CLEAN AMBI – Clean tone with big reverb and delay.
MAKING ADJUSTMENTS FOR YOUR SETUP
SETTING THE PATCH UP FOR YOUR GUITAR
All guitars are different, so you may want to make changes to suite your playing style and guitar. We set this up with a variety of guitars, including both single coils and humbuckers (primarily a Telecaster style guitar). If your guitar has humbuckers, please refer to the suggested settings below.
We recommend making a copy of the patch and changing the copy just in case you want to revert back to the original.
We’ve included both single coil and humbucker voiced patches to serve as starting points for your guitars. To make adjustments, we recommend starting with these parameters:
- Amp Gain: Adjust the min/max values of the amp gain so that your guitar is slightly breaking up with big chords on the bridge position (without any drive pedals on)
- Amp EQ controls: Adjust these to suite your individual guitars/taste
- EQ block: This is a simple way to adjust the overall tonal characteristics of the patch.
VOLUME CHANGES
If you would like to make this patch louder or quieter without affecting tone, the following adjustments can be made:
“Ch Vol” control on the amp module. This will increase or decrease volume without affecting the tone of the amp. This is the primary level adjustment tool I use for changing patch volumes.
Output block level. Changing the level control on the output block (the very last thing in the signal chain) will increase or decrease overall volume. We typically have this set at zero, but feel free to adjust this as you see fit.
CHANGELOG
Version 1.0 (initial release): 2021-10-27
Reviews
There are no reviews yet.